色亚洲91。,69re性视频,青青青在线播放,日本午夜aa电影,av影视二区,午夜成人集群视频,精选人妻久久区,成人在线你懂得,日韩情色免费在线观看

●應用:
???該螺桿泵可用于輸送中性或腐蝕性的液體,潔凈的或磨損性的液體,含有氣體或易產生氣泡的液體,高粘度或低粘度的液體,包括含有纖維物和固體物質的液體.
??G型單螺桿泵系列,是我廠主要系列產品,應用極為廣泛.
???GS系列泵是由G型基本系列發展來的,區別在于特殊的泵體,"S"的意義是快速清潔,每個零件的任一細小部位都能被清潔得非常干凈.
???食品業:用于酒廠輸送酒,廢渣及制酒流程中的投配料的輸送.
???紡織業:用于輸送合成纖維,黏膠液,染料,油墨,尼龍粉液.

???造紙業:用于紙漿黑液的輸送.
???石油業:用于多種油類,油脂產品的地面集輸泵.
???化工業:用于輸送各種懸浮液,乳膠業,酸,堿,鹽液.
???造船業:用于輸送渣油,掃艙和污水,海水等.
???建筑業:輸送灰漿,灰膏.
???核工業:輸送帶顆粒的放射性液體.
???電廠:用于水煤漿的輸送 .
???●G型單螺桿泵設計特點:
???1.聯軸器兩端采用一字銷萬向節接頭,其銷子和銷套是由特殊材料制成的,因而其壽命得到了很大的改
善,其結構簡單容易拆卸見.
???2.襯套兩端有包過來的橡膠使其與進出管聯接處密封可靠從而保證了襯套體不受到腐蝕
???3.在吸入管和軸承體之間裝有一個可進行更換的填料箱,既能用于填料密封又能用于機械密封(可進行
不同形式的密封更換).
???4.GS 系列吸入管和壓出管的聯接是標準DIN1187-A的螺紋聯接,可以快速拆卸吸入和壓出兩側的管子
和軟管.

臥式單螺桿泵操作保養規定:Horizontal single screw pump operation maintenance provisions:
???? 一、操作規程? 1、檢查流程是否正確。? 2、檢查聯軸器保護罩，地腳等部分螺絲是否緊固，有無松動現象。 3、軸承油盒要有充足的潤滑油，油位應保持在規定范圍內，油質是否完好。? 4、檢查電壓是否在規定范圍內，外觀電機接線及接地是否正常。 5、用手盤動聯軸器，檢查泵內有無異物碰撞雜聲或卡死現象，并給予消除。? 6、停車前需先停止電機運行，后關閉吸入管閥門，再關閉排出口閥門（防止干轉，以免擦傷工作表面）。A, operating rules 1, check whether the process is correct.2, check the coupling shield, whether the anchor parts such as screw fastening, the presence of loose phenomenon.3, bearing oil box should have plenty of oil, oil level should be kept within the prescribed scope, oil are in good condition.4, check whether the voltage is within the scope of the regulations, electrical wiring and grounding are normal in appearance.5, with the hand disc coupling, check there are no foreign bodies collide in the pump noise or jammed phenomenon, and to give away.Need before 6, parking to stop the motor running, after close the suction valve, then close the discharge valve (turn to prevent dry, so as not to scratch working surface).
???? 二、維護保養? 1、檢查軸封及各接合密封面是否有泄漏；? 2、檢查冷卻系統是否暢通，壓力、溫度是否在合理范圍； 3、檢查運轉的平穩性，是否有振動； 4、檢查機座螺栓是否松動；? 5、長時間停車應排凈系統中的物料，氣溫較低時檢查防凍防凝情況。 2, 1, check the shaft seal and the maintenance of joint sealing surface whether there is leakage;2, check whether the cooling system is open, pressure, temperature is in the reasonable scope;3, check the operation stability, whether to have vibration;4, check whether the mounting bolts is loose;5, stop for a long time should be no net system of material, the temperature is lower check antifreeze anti coagulation conditions.
???? 三、注意事項? 1、啟動前一般應全開入口閥、出口閥，打開出口閥后，應盡快將泵啟動。嚴禁在沒有打開出口閥的情況下開泵（如果出口閥關閉，必須保證出入口連通閥全開）。? 2、嚴禁在沒有灌泵的情況下長時間運轉。? 3、出現下列情況立即停泵：嚴重泄漏、異常振動、異味、火花、煙氣、撞擊、電流持續超高等現象。? 4、螺桿泵在運行過程中,軸承溫度不能超過環境溫度35℃,最高溫度不得超過80℃. 1, before the start of the general considerations should be fully open the inlet valve and outlet valve, open the outlet valve, should will pump start as soon as possible.Is strictly forbidden in the absence of open the outlet valve opening pump (if the outlet valve closed, must ensure that the gateway connected valves).2, it is strictly prohibited in the absence of irrigation pump long time running.3, stop the pump immediately in the following circumstances: serious leakage, abnormal vibration, bad breath, a spark, flue gas, such as collisions, current ultra-high phenomenon.4, screw pump in the process of operation, the bearing temperature cannot exceed ambient temperature 35 ℃, the highest temperature should not exceed 80 ℃.